–>
Clear Water Based Acrylic Sealer
SATIN-SEAL / SPE-SS is a one component lower gloss water based acrylic sealer that offers excellent resistance to water blushing without the objectionable solvent odors associated with solvent based sealers. This product has a fast set time and good .
Choose Size
1 Gallon Kit (+$97.70)
5 Gallon Kit (+$428.30)
50 Gallon Drum (+$4,249.28)
Add to Cart
VIDEO AND INSTRUCTIONS
Videos and Instructions
EXPERT HELP
FREQUENTLY ASKED QUESTIONS
DURABLE
Large Project? Get a Quote Here
SATIN-SEAL / SPE-SS is a one component lower gloss water based acrylic sealer that offers excellent resistance to water blushing without the objectionable solvent odors associated with solvent based sealers. This product has a fast set time and good stain resistance. Recommended for sealing concrete or cement. Do not use in immersion service or constant chemical exposure areas.
401 to 533 Sq Ft per gallon @ 3 to 4 mils wet thickness.
INSTRUCTIONS (SATIN-SEAL / SPE-SS)
1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 60 and 90 degree F. Keep from freezing.
2) SURFACE PREPARATION: Surface preparation will vary according to the type of substrate. For a one or two coat thin build application (3-8 mils wet) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. All dirt, oil, dust, foreign contaminants and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete has an appropriate vapor barrier. This can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate does not show signs of eventual hydrostatic pressure problems that may later cause disbonding. However, this product can be applied to a damp floor as long as there are not standing puddles.
3) PRODUCT MIXING: This product should be stirred well before using. Mix with slow speed mixing equipment to avoid introducing air into the material.
4) PRODUCT APPLICATION: The material can be applied by brush or roller. Maintain temperatures and humidity within the recommended ranges during the application and curing process.
5) RECOAT OR TOPCOATING: If you opt to recoat this product, you must first be sure that all of the solvents and water have evaporated from the coating during the curing process. The information on the front side are reliable guidelines to follow. However, it is best to test the coating before recoating. This can be done by pressing on the coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat or topcoat can be started. Always remember that colder temperatures will require more cure time for the product before recoating can commence. We do not recommend any coatings be placed over this product except multiple coats of this product itself.
6) CLEANUP: Use Soap and Water
7) FLOOR CLEANING: Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.
8) RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry.
INSTANTLY BUILD YOUR FLOOR WITH OUR KIT BUILDERS! Metallic EPOXY OR DECORATIVE FLAKE NEED HELP? TALK TO A TRUE EXPERT 1-877-288-1952
Are you part of a Government Agency, Military Branch or Architect that needs Scope of Work documents? SCOPE OF WORK AND GUIDES
NEED INSPIRATION? VIEW OUR FLAKE AND METALLIC COLOR CHARTS FLAKE CHART OR METALLIC CHART NEED HELP? TALK TO A TRUE EXPERT 1-877-288-1952
Clear Water Based Sealer 401
–>
SKU: UPC: Shipping: Calculated at Checkout
- Fast Shipping Australia Wide
- Quality Sealers Made In Australia
- Safe Payments Trusted SSL Protection
- Free Samples Try Before You Buy
Seal and Protect Surfaces
Clear Water Based Sealer 401 is a hardwearing, clear coating designed to protect a wide range of surfaces including masonry, concrete and internal timber.
When cured it provides a smooth washable surface that will keep the surface dry and protect it from stains and spills.
Easy To Apply
This product can be applied over damp surfaces and the sheen level increased by applying additional coats as required. Two coats will provide a satin finish over smooth surfaces.
The advanced self cross-linking polymer cures after 72 hours and provides excellent chemical and water resistance and extended exterior durability.
Rapid Drying Time
Clear Water Based Sealer 401 is a rapid dry coating allowing the applicator to apply multiple coats in a single day.
Wet on wet application is possible where projects need to be completed in a short time.
Allow the coating to turn clear before applying subsequent coats.
Anti-Slip Additive
This sealer may become slippery when wet on some surfaces such as smooth pavers and terracotta or ceramic tiles. An anti-slip powder can be added to the final coat to increase texture and reduce slip hazards when used on steep grades or surfaces subject to frequent wetting with water.
More information on our anti-slip powder can be found on our product page.
Click Here To View
Product Data Sheet
- Product Description
Clear Water Based Sealer 401
Designed for use on a wide range of substrates, Clear Water Based Sealer 401 will seal and protect surfaces keeping the clean, protecting them from spills and stains, so they stay looking great for years.
Being a water-based product makes for easy application and the rapid dry formula makes it ideal for projects that need to be completed in a day.
- Will not blush or water whiten even under constant exposure to moisture
- UV resistant and can be used in exposed exterior areas
- Dirt and stains can be cleaned off with a mild detergent
- Suitable for indoor and outdoor use
- Low VOC
Coverage rate 1L = 5m²
PLEASE NOTE: This is a water based sealer and therefore not compatible with solvent based sealers. If you are re-sealing a surface and unsure, you should test an area with our ‘399 Solvent’ prior to application.
Here are some photos from Greg, who is a customer that purchased our 401 product and used it on his finished interior aggregate floor.
